The Orangutan SVP robot controller is a complete control solution for small and medium-sized robots running at 6 – 13.5 V. The module is designed around the powerful Atmel ATmega324PA AVR microcontroller (32 KB flash, 2 KB RAM, and 1 KB EEPROM) or ATmega1284P (128 KB flash, 16 KB RAM, and 4 KB EEPROM) running at 20 MHz and features a full complement of peripheral hardware to support robotics applications. For a detailed description of the Orangutan SVP’s capabilities, please see the product page for the fully assembled SVP-324 or fully assembled SVP-1284.
The Orangutan SVP partial kit PCB has all of the surface-mount components pre-soldered, as shown to the right, and the kit includes the following through-hole components so that you can customize the robot controller to your particular application:
- Six 3×4 male header blocks
- Six 3×4 female header blocks
- One 3×7 male header block
- One 3×7 female header block
- Three 2-pin 3.5mm terminal blocks
- Five blue shorting blocks
- Two 2×3 female header blocks
- One 2×3 shrouded box header
- One 2×8 shrouded box header
- One buzzer
- Five pushbuttons
- One 2×20 breakaway male header
- One 1×20 breakaway male header
- Five 1×2 female header blocks
- Two single-pin female headers
Like the fully assembled version, the kit includes a USB A to mini-B cable.
The Orangutan SVP partial kit does not include an LCD. Our 16×2 LCDs (both with backlight and without) can be plugged directly into the PCB if you solder a 2×7 female header to the left side of the LCD and two single male pins to the right side of the LCD. These two male pins provide structural support for the LCD and power the backlight on the version with a backlight. You can connect your own parallel-interface (HD44780) LCD, such as our 20×4 LCD to the LCD port via a 16-conductor ribbon cable.
Since the Orangutan SVP partial kit includes headers of both genders, you have the ability to solder in the gender that best suits the peripherals you plan to connect to the board, or you could go for an even more compact installation and solder your peripherals directly to the I/O pads. Since the buzzer and pushbuttons are not pre-soldered, you can replace these with components of your choosing, such louder speakers (the Orangutan SVP powers the buzzer through a transistor rather than a microcontroller I/O pin, so it can support much higher-power speakers than previous Orangutans) and bigger buttons located off of the board.
|Size:||3.70" x 2.20"|
|Processor:||ATmega1284P @ 20 MHz with auxiliary PIC|
|RAM size:||16384 bytes|
|Program memory size:||128 Kbytes|
|Motor driver:||Dual TB6612FNGs|
|User I/O lines:||211|
|Max current on a single I/O:||40 mA|
|Minimum operating voltage:||6 V|
|Maximum operating voltage:||13.5 V|
|Continuous output current per channel:||2 A|
|Peak output current per channel:||6 A|
|Current sense:||0.85 V/A|
|Maximum PWM frequency:||80 kHz|
|Reverse voltage protection?:||Y|
|External programmer required?:||N|
Documentation and other information
User’s guide for the Pololu Orangutan SVP-324 and SVP-1284 robot controllers (both assembled and partial-kit versions).
This guide explains how to get started programming your Orangutan or 3pi Robot in Windows, Linux or Mac OS X. It covers setting up an AVR development environment (Atmel Studio for Windows users), installing the Pololu AVR C/C++ Library, and setting up the Pololu USB AVR Programmer.
Information about installing and using the C/C++ libraries provided for use with Pololu products.
A reference to commands provided in the Pololu C/C++ and Arduino libraries for the AVR.
Guide for programming Orangutans and the 3pi robot from the Atmel’s older AVR Studio 4 IDE. It covers installing the Pololu AVR C/C++ Library, and setting up the Pololu USB AVR Programmer.
- Pololu AVR Development Bundle for Windows (12MB exe)
- This bundle contains all the Pololu software you need to get started programming AVRs in Windows: the Pololu AVR C/C++ Library, the Pololu USB AVR Programmer drivers and software, and the Pololu Orangutan SVP drivers. We recommend installing Atmel Studio 7.0 before installing this bundle.
- Orangutan SVP Drivers for Windows (version 121115) (53k exe)
- This executable installer contains the drivers you need to use the Orangutan SVP in Windows.
- Orangutan SVP Reference Diagram (82k pdf)
- This printable quick-reference diagram identifies all the interactive components on the Orangutan SVP, including the pins, pots, LEDs, and pushbuttons.
- Orangutan SVP Schematic Diagram (99k pdf)
- Sample AVR Studio 4 project for the ATmega324PA to blink an LED (7k zip)
- This is a sample AVR Studio 4 project that will blink an LED on an Orangutan SVP-324.
- Sample AVR Studio 4 project for the ATmega1284P to blink an LED (8k zip)
- This is a sample AVR Studio 4 project that will blink an LED on an Orangutan SVP-1284.
- Toshiba TB6612FNG motor driver datasheet (308k pdf)
- Orangutan SVP guia de usuario (2MB pdf)
- A Spanish version of the Orangutan SVP robot controller user’s guide, provided by customer Jaume B.
- Orangutan SVP desktop background, 1280×768 (438k jpg)
- Orangutan SVP desktop background, 1280×768, no LCD (521k jpg)
Be The First To Review This Product!
Help other Little Bird Company Pty Ltd users shop smarter by writing reviews for products you have purchased.